View

 

 

What're your concepts on A Step-by-Step Guide to Installing a Bathtub?

Mounting a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily available, the project can move speedily; if you need to open up a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub as well as set in the new one. See to it you have actually certified yourself for the job and fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bath tub in your restroom if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.

 

 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.

 

 

Installing the Bathtub

Using the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has actually been used at the very least when as this will resolve it right into its final placement.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin ensuring that the washing machines remain in place in between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you liked our piece about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking time to read through our post. Appreciated our article? Please share it. Help another person check it out. Thank-you for taking the time to read it.

Click Here!